Load Cell 10 VDC

Bonded foil Strain Gauge Load Cell

Standard Model Includes:

• Type: Bonded foil strain gauge
• Excitation: 10 VDC
• Bridge Resistance: 350 ohms

  Specifications
  The load cell allows very accurate recording of the test load.
  The electronic strain gauge load cell is an independent measuring system not tied to the hydraulic system.
  This load cell system, with two ranges, may be calibrated from 1% to 100% of the maximum capacity of the load cell. The load cell will calibrate to ASTM E-4, +/- 1%, traceable to the United States National Institute of Standards and Technology (NBS).

• Handheld Readouts.
• Made from a Lightweight Aerospace Alloy.
• Available Hermetically sealed for use in wet conditions.
• Units have a 5 metre cable close coupled to a 4 digit 15mm LCD display.
• Tare, Peak and Reset facility.
• The power source is a 9V PP3 battery, can be supplied for mains power if required (240v).
• All units are calibrated to comply with ISO 7500-1: 2004.
• The accuracy of the cells are better then 1% of applied load.
• Complete with carry case.
• 12 Month Guarantee, subject to conditions.

  Options:
  12V Mains Operation
  Monitor can be supplied with a socket for operation from a mains plug top, 240 to 12 volt power supply.
  The unit can be scaled Tonne, Kilograms or KN’s
  The above can be supplied with longer monitor cables if required
  Range of sizes we offer are: 4,000lb, 10,000lb, 20,000lb, 40,000lb, 10,000lb & 200,000lb. Plus specials

Click here for the full Accuway TM specification...
Click here to download Accuway TM specification PDF

Accuway CM with handheld readouts

• Handheld Readouts.
• Made from a Lightweight Aerospace Alloy.
• Available Hermetically sealed for use in wet conditions.
• Tare, Peak and Reset facility.
• Units have a 5 metre cable close coupled to a 4 digit 15mm LCD display.
• All units are calibrated to comply with ISO 7500-1: 2004.
• The accuracy of the cells are better than 1% of applied load.
• The power source is a 9V PP3 battery, can be supplied for mains power if required (240v).
• 12 Month Guarantee, subject to conditions.
• Complete with carry case.

  Options:
  12V Mains Operation
  Monitor can be supplied with a socket for operation from a mains plug top, 240 to 12 volt power supply.
  The unit can be scaled Tonne, Kilograms or KN’s
  The above can be supplied with longer monitor cables if required
  Range of sizes we offer are: 2.0 tonne, 5.0 tonne, 10.0 tonne, 20.0 tonne, 50.0 tonne & 100.0 tonne. Plus specials

Click here for the full Accuway CM specification...
Click here to download Accuway CM specification PDF

Accuway TMIR - Infrared Operation

• The cell is manufactured in aluminium alloy with HT steel bushes.
• The cell incorporates an eight gauge bridge together with associated electronics and a 9 volt PP3 non-rechargeable battery.
• Built into the load cell is a large [20mm] 3.5 digit liquid crystal display mounted on the front of the cell for easy reading from the operator’s position.
• The load cell is self contained and has no external cabling.
• A battery switch is provided on the rear of the cell to prolong battery life when the cell is out of use.
• All set up and calibration data is retained when switched off.
• The cell is automatically switched off after 15 minutes to prolong battery life.
• Battery life – typically 50 hours.
  
  Note :- The tare and peak readings are stored even after an automatic 15 minute shut down, the tare and peak reading being returned at next ‘on’ press of the remote, [provided the cell rear button has not been switched off.] * Automatic range change is available when appropriate.
  

Accuway TMIR - Infrared Operation

• Control is via a hand held controller.
• Size – 95 x 60 x 40 mm.
• Battery – 1 x PP3 non-rechargeable
• Battery life – many tens/hundreds of hours depending on use.
• Mounted on the controller are four momentary action push buttons. These buttons perform the following functions :- On/Off.
• Zero/Tare – button will tare up to 10% of cell capacity.
• Peak – retains the highest load applied since selecting Peak or resetting.
• Reset – resets the peak reading
• Range – The infrared controller will operate in bright ambient light conditions, however, it will not operate if the cell is directly facing into the sun.
• The minimum range is 5 metres, typically 7 metres.
  

Click here to download Accuway TMIR specification PDF

Accuway SMIR - Infrared Operation

• The cell is manufactured in aluminium alloy with HT steel bushes.
• The cell incorporates an eight gauge bridge together with associated electronics and a 9 volt PP3 non-rechargeable battery.
• Built into the load cell is a large [20mm] 3.5 digit liquid crystal display mounted on the front of the cell for easy reading from the operator’s position.
• The load cell is self contained and has no external cabling.
• A battery switch is provided on the rear of the cell to prolong battery life when the cell is out of use.
• All set up and calibration data is retained when switched off.
• The cell is automatically switched off after 15 minutes to prolong battery life.
• Battery life – typically 50 hours.
• Available in 4,000lb, 10,000lb & 20,000lb
  
  Note :- The tare and peak readings are stored even after an automatic 15 minute shut down, the tare and peak reading being returned at next ‘on’ press of the remote, [provided the cell rear button has not been switched off.] * Automatic range change is available when appropriate.
  

Accuway SMIR - Infrared Operation

• Control is via a hand held controller.
• Size – 95 x 60 x 40 mm.
• Battery – 1 x PP3 non-rechargeable
• Battery life – many tens/hundreds of hours depending on use.
• Mounted on the controller are four momentary action push buttons. These buttons perform the following functions :- On/Off.
• Zero/Tare – button will tare up to 10% of cell capacity.
• Peak – retains the highest load applied since selecting Peak or resetting.
• Reset – resets the peak reading
• Range – The infrared controller will operate in bright ambient light conditions, however, it will not operate if the cell is directly facing into the sun.
• The minimum range is 5 metres, typically 7 metres.
  

Click here to download Accuway smir specification PDF